Model SAO-2734030810-KF-S1 is a full band, WR-28 omnidirectional antenna that operates between 26.5 and 40 GHz. This vertically polarized antenna offers 360 degrees azimuth coverage. 

Model STE-SF908-00-S1 is an F-Band X9 frequency extender that uses an input frequency range of 10 to 15.56 GHz at +5 dBm along with harmonic generation and filtering.

STQ-TO-12-U3-CKIT1 is an E-band waveguide vector network analyzer (VNA) calibration kit designed to work with industry standard network analyzers in the frequency range of 60 to 90 GHz.

TF-04-S1 SAGE Millimeter, Inc. model STF-04-S1 is a full band Faraday isolator that operates from 170 to 260 GHz. The Faraday isolator offers 30 dB typical isolation and 4.0 dB nominal insertion loss with good flatness.

SAGE Millimeter’s model SAF-2434231535-358-S1-280-DP is a dual polarized, scalar, feed horn antenna assembly that covers all 5G frequency bands in the range from 24 to 42 GHz. Both modes benefit from 15 dBi of mid-band gain.

Model SAT-363-25028-C1 is a WR-28 orthomode transducer (OMT) that operates between 30  and 42 GHz. The OMT separates a circular or elliptical polarized waveform into two linear, orthogonal waveforms or combines two linear polarized waveforms into one circular or elliptical polarized waveform or vice versa.

Model SFB-50375308-1519KF-N1 is a V-band balanced mixer with U band LO port that utilizes high performance GaAs Schottky beam-lead diodes and a balanced circuit configuration to offer superior RF performance. RF frequency of 50 to 75 GHz and an LO frequency of 40 to 60 GHz.

Model STB-5037032515-1515-S1 is a broadband benchtop driver amplifier with a typical small signal gain of 25 dB, a nominal P_1dB of +15 dBm and P_sat of +18 dBm across the frequency range of 50 to 70 GHz. The power supply required is a single phase AC voltage in the range of 100 to 240 V_AC, which can be supplied by a wall outlet.

Model STE-SF415-15-S1 is a high ouput power V-Band X4 frequency extender that uses an input frequency range of 12.5 to 18.75 GHz at +5 dBm along with harmonic generation and filtering to produce a 50 to 75 GHz RF signal at +15 dBm. The extender is designed and manufactured as a bench top unit to extend the low frequency synthesizer or sweeper without losing all of the functionalities and features.

Model SBL-1141741860-0606-V1 is a D band low noise amplifier with a typical small signal gain of 18 dB and a nominal noise figure of 6.0 dB across the frequency range of 110 to 170 GHz.  The DC power requirement for the amplifier is +3 V_DC/60 mA. The input and output port configuration offers an inline structure with WR-06 waveguides and UG-387/U-M flanges.

Model SAC-0432433012-SF-S4-DP-QR is a quad ridge dual polarized conical horn antenna that operates from 4 to 24 GHz. The antenna offers a 12 dBi nominal gain, a typical half power beamwidth of 40 degrees on the E plane and 30 degrees on the H plane at the center frequency of 14 GHz. The nominal side lobe levels are -12 dB or lower. The horn antenna is equipped with SMA(F) connectors. 

Model SBP-5037032518-1515-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal P_1dB of +18 dBm across the frequency range of 50 to 70 GHz.  The DC power requirement for the amplifier is +8 V_DC/650 mA.  The mechanical configuration offers an in line structure with WR-15 waveguides and UG-385/U flanges. 

Model STE-SF612-15-S1 is a high ouput power E-Band X6 frequency extender that uses an input frequency range of 10 to 15 GHz at +5 dBm along with harmonic generation and filtering to produce a 60 to 90 GHz RF signal at +15 dBm. The extender is designed and manufactured as a bench top unit to extend the low frequency synthesizer or sweeper without losing all of the functionalities and features.

The quadrature mixer, commonly known as the I/Q mixer, is configured with two individually balanced mixers and their respective LOs driven from the outputs of a 90-degree hybrid. It is widely used when single sideband (SSB) rejection is required.

Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC / 150 mA. The mechanical configuration offers an in line structure with WR-15 waveguides and UG-385/U flanges.

For communication, radar and test applications, SAGE Millimeter has released a W-Band Varactor tuned Gunn oscillator. Model SOV-94306310-10-G1 utilizes a high-performance GaAs Gunn diode and proprietary cavity design to deliver +13 dBm typical power. The oscillator features a Varactor tuning range of ±3 GHz and delivers low AM/FM noise and harmonic emissions.

Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges.

SAGE Millimeter has released a V-Band, dual polarized horn antenna assembly covering 50 to 75 GHz. The antenna features an integrated orthomode transducer (OMT) that provides high port isolation and cross-polarization cancellation, enabling the antenna to separate a circular or elliptical polarized waveform into two linear, orthogonal waveforms. At the center frequency, the horn antenna has 15 dBi nominal gain and a typical half-power beamwidth of 28 degrees on the E-plane and 33 degrees on the H-plane.

As an addition to its passive waveguide product offering, SAGE Millimeter, Inc. has released a line of flexible waveguides to cover 18 to 50 GHz. The flexible waveguide line is manufactured with a precision machining process to ensure high quality and ruggedness. Furthermore, all standard models feature a vulcanized silicone rubber jacket for added protection and reliability. 

SAGE Millimeter Inc. has released a series of broadband circulators and isolators that cover the frequency range of 71 to 76 GHz and 81 to 86 GHz. The circulators, models SNW-7137630818-12-C1 and SNW-8138630818-12-C1, and isolators, models SNW-7137630818-12-I1 and SNW-8138630818-12-I1, provide a low insertion loss of 0.8 dB maximum, a minimum isolation of 18 dB, and a short insertion length for system integration. 

Model SAO-2832930610-28-S1 is a WR-28 omnidirectional antenna that operates between 28 and 29 GHz. This vertically polarized antenna offers 360 degrees azimuth coverage with 6 dB gain and ±3 dB gain flatness. The antenna features a half power beamwidth of 10 degrees in the vertical direction. The actual operating frequency of this omnidirectional antenna is much broader.

Model STO-12-S1 is an E Band vector network analyzer (VNA) frequency extender designed to achieve full 2-port, S-parameter testing at 60 to 90 GHz.  It is compatible with modern vector network analyzers such as the Rohde & Schwarz ZVA Series and the Keysight PNA-X Series. The frequency extenders can achieve a dynamic range of 90 dB and are great for testing many E band devices including passive and active devices.

Models SWF-65302350-15-B1, SWF-61302350-15-B1, SWF-63302350-15-B1 and SWF-58302350-15-B1 are V band, waveguide bandpass filters designed for WiGig applications. All four filters offer a 2 GHz passband with 50 dB typical rejection. The filters also have a nominal insertion loss of 2.5 dB. Since both low and high end cut off frequencies can be selected by modifying the design, custom models are available.

Model SOM-94308315-10-M1is a W-Band mechanically tuned gunn oscillator utilizing a high performance InP Gunn diode and proprietary cavity design to deliver +15 dBm typical power directly with a frequency tuning range of 90 to 98 GHz. Product delivers low AM/FM noise and harmonic emissions in the wide mechanical tuning range. The Gunn oscillator is equipped with a micrometer tuner for quick frequency tuning and setting as bench top equipment.

Model SFS-73336315-12SFKF-E1-M is an E Band sub-harmonically pumped mixer that utilizes high performance GaAs MMIC chips to offer superior RF performance. The required LO frequency and power are 35 to 38 GHz and +16 dBm, respectively. The mixer exhibits 15 dB nominal conversion loss in the RF frequency band of 70 to 76 GHz. The amplitude unbalance is within ±1 dB and phase unbalance is ±20 degrees typically. IF frequency bandwidth is from DC to 5 GHz.

Model SSR-9630831560-10-S1 is a W-Band receiver. The receiver has a typical conversion gain of 15 dB with a typical RF input power of -60 dBm in the frequency range of 92 to 100 GHz and an IF output frequency range of DC to 4 GHz. The required LO power and frequency range are +5 dBm and 16.0 GHz . The LO and IF port are both equipped with female SMA connectors and the RF port is a WR-12 waveguide with a UG-387/U flange.

Model SWF-74305350-12-B1 is an E band, waveguide bandpass filter that is used to pass the frequency range of 71 to 76 GHz, while rejecting the frequency range of DC to 67 GHz and 81 to 90 GHz. The nominal insertion loss of the bandpass filter is 2 dB and the typical rejection is 50 dB. The standard interface offers WR-12 waveguides with UG-387/U flanges. Various custom models are available.

Model SSC-7737731200-1212-C1 is an E-Band transceiver. The transceiver has a minimum transmit output power of -30 dBm in the frequency range of 76 to 78 GHz with an IF input power of 0 dBm in the frequency range of 550 to 950 MHz. The typical receive conversion loss is -12 dB with a typical RF input power of -20 dBm in the frequency range of 76 to 78 GHz and a IF output frequency range of 550 to 950 MHz.

Model SSK-ST573673-15-ITS1 is a V-Band transmitter (upconverter) that emits two orthogonally polarized signals from 57-67 GHz. The transmitter takes 14.250 to 15.875 GHz/+0 dBm signal through a X4 active multiplier to generate millimeterwave signal as its local oscillator and DC to 3.5 GHz/0 dBm as its IF input signal to generate 57 to 67 GHz RF signals.

Model SBP-2634034530-2828-X1 is a full Ka band power amplifier with a typical small signal gain of 45 dB and a typical P1dB of +30 dBm in the frequency range of 26.5 to 40 GHz. The typical DC power requirements for the amplifier are +6 VDC/2,500 mA and -5.0 VDC/110 mA, respectively. The input and output port configurations are both WR-28 waveguide with UG599/U flange.

Model SST-2730253027-28-S1 is a Ka Band compact transmitter module operating at 26.8 GHz. This product is designed and manufactured for small satellite applications. The module incorporates a phase locked oscillator to convert 1.0 signal to 26.8 GHz signal. With an integrated 23 dBi circular polarized lens corrected antenna, the module delivers +50 dBm EIRP. The module measures 3.78”(W) x 3.44”(L) x 4.43” (H) and weighs 24 Oz.

Model SBL-5037533060-1212-E1 is a low noise amplifier covering the full waveguide band from 50 to 75 GHz with small signal gain of 30 dB and 6.0 dB noise figure. The amplifier also exhibits +10 dBm typical P-1 dB output powers.  It draws about 120 mA current from a single DC power supply in the range of +8 to +12 volts.

Model SWP-46347304-2F2F-C1 is a Q band high Q four-way power combiner operating from 45.5 to 47 GHz. The power combiner exhibits better than 15 dB return loss, 2.0 dB insertion loss and 20 dB port to port isolations in the operational bandwidth. The power combiner possesses excellent phase and amplitude balanceand is equipped with 2.4 mm (female) connectors.

Model SKD-9031045030-1010-R1 is a W-Band single-pole double-throw (SPDT) switch that operates from 90 to 100 GHz. It has better than 30 dB isolation and 5 dB typical insertion loss over the entire frequency range. The power handling and input P-1 dB of the switch is +23 dBm CW. This model has a built-in TTL driver which provides 2 us switching speed. The required bias for the switch is +/- 5 Vdc/10 mA.

Model SAM-3533532205-28-L1 is a micro-strip patch array antenna with rectangular waveguide interface. The antenna is constructed with higher performance and low loss soft microwave substrates. Various power distribution arrangements, such as corporate-fed or series-fed, are implemented to achieve the best aperture efficiency and antenna performance. The patch array antenna offers high gain and very low side lobes.

Model SBB-0132732526-KFKF-SB is a bench-top broadband power amplifier operating from 1.0 to 26.5 GHz. The amplifier provides 25 dB small signal gain and a minimum +25 dBm output power over the entire frequency range. The bench top amplifier is designed to use 100 to 240 V AC power directly from power line for laboratory use. The bench top amplifier is equipped with K connectors for RF path and measures 3.75” (W) x 4.15” (L) and 1.75” (H).

Model SOD-26303230-KF-S1 is a 26 GHz dielectric resonator oscillator (DRO). The oscillator is a free running oscillator with high frequency stability which is achieved by implementing a high quality dielectric resonator. The oscillator exhibits +30 dBm output power and low phase noise of -100 dBc/Hz at 100 KHz offset. The frequency stability of the oscillator is +/- 4 ppm or better in the temperature range of -40 to +85 °C.

Model SAL-7531143004-10-S1 is a W band lens corrected antenna with frequency range from 75 to 110 GHz. The antenna has 4 degree half power beamwidth with a typical of 30 dBi gain. The antenna is equipped with a rectangular WR-10 waveguide and UG-387/ U-M flange, which supports linear polarized waveforms. The lens corrected antennas cover the frequency range from 8.2 to 140 GHz.

Model SBP-8138632018-1212-S1 is an E-Band high power amplifier with small signal gain of 20 dB minimum and P1dB of +18 dBm in the frequency range of 81 to 86 GHz. The DC power requirement for the amplifier is +8 VDC/650 mA. The input and output port configurations are both WR-12 waveguides with UG387/U flanges.

Model SBL-0524034260-KFKF-SB is a bench-top broadband low noise amplifier operating from 0.5 to 40 GHz. The amplifier exhibits 42 dB small signal gain and average 6 dB noise figure over the entire frequency range. The minimum P-1 dB is +10 dBm. The bench-top amplifier is designed to use 100 to 240 V AC power directly from lab outlets.

Model STZ-15-I1 is a V Band full waveguide noise source. The noise source is silicon IMPATT diode based solid state noise source, which employs high performance diode and priority circuit design to offer nominal 14 dB ENR with extreme flatness in entire waveguide bandwidth from 50 to 75 GHz.

Model SWP-46347304-2F2F-C1 is a Q band high Q four-way power combiner operating from 45.5 to 47 GHz. The power combiner exhibits better than 15 dB return loss, 2.0 dB insertion loss and 20 dB port to port isolations in the operational bandwidth. The power combiner possesses excellent phase and amplitude balance. The power combiner is equipped with 2.4 mm (female) connectors.

Model SAO-5836230230-15-S1 is a V Band vertically polarized omni-directional antenna with center frequency at 60 and ± 2 GHz operation bandwidth. The antenna is designed for close-in wireless communication applications. The antenna has 30 degree vertical beam width with a typical 2 dBi gain.

Model STG-12-S1 is an E-Band noise figure and gain test set, which includes a high performance solid-state E-Band noise source (STZ-12-I1) and a full waveguide band down converter (STC-20-12-S1). It extends the noise and gain measurement capacity from 10 to 15 GHz to the frequency range of 60 to 90 GHz.

Model SSC-7737731200-1212-C1 is a compact and cost-effective E band transceiver module operating in the frequency range of 76 to 78 GHz. The module is designed and fabricated for emerging automotive ACC radar applications. It can be used as FMCW transceiver for speed and distance measurements or radar target simulators for testing.

Model SFA-713863410-12KF-S1 is a 71 to 86 GHz X4 active multiplier which is designed for E-Band communications and automotive radar applications. The active multiplier converts 17.75 to 21.5 GHz / +5 dBm input signal to deliver 71 to 86 GHz frequency band with a typical +10 dBm output power.

Model SBL-7531142240-1010-S1 is a W band low noise amplifier covering entire W-band from 75 to 110 GHz .  The amplifier exhibits more than 20 dB small signal gain with ± 1.5 dB gain flatness and around 4.0 dB noise figure. The output P-1 dB of the amplifier is around 0 dBm typical and it draws 30 mA current from a single DC power supply in the range of +5 to +12 volts.

Model STZ-12-I2 is an E Band noise source with extremely high ENR. The noise source is silicon IMPATT diode based solid state noise source, which employs high performance diode and priority circuit design to offer minimum 20 dB ENR in entire waveguide bandwidth from 60 to 90 GHz. 

Model STN-SF908-00-P2 is an F band scalar network analyzer extender covers the frequency range of 90 to 140 GHz. It offers an alternative way of allowing users to achieve millimeter wave scalar measurement in a low cost approach without losing any of the functionalities and features that the industry standard models have to offer.

Model STC-20-10-S1 is a W band full waveguide band down converter with an RF range of 75 to 110 GHz. The full waveguide band down converter requires a +10 dBm LO signal in the frequency range of 12.5 to 18.33 GHz. It converts 75 to 110 GHz input signal to 10 MHz to 1.6 GHz output signal with a typical conversion gain of 20 dB. The required DC input is +12 Vdc / 450 mA.

Model SFA-923963618-10SF-S1 is a W-Band X6 active multiplier with center frequency at 94 GHz with minimum ± 2 GHz operational bandwidth. The active multiplier converts 15.33 to 16.0 GHz/+5 dBm input signal to deliver 92 to 96 GHz frequency band with more than +18 dBm power.

Model SWP-50366308-15-C1 is a V band waveguide eight-way power combiner operates from 50 to 66 GHz. The power combiner exhibits 2.0 dB insertion loss and 18 dB port to port isolations between non-adjacent ports and 13 dB between adjacent ports in the operational bandwidth.

Model SAF-2733331624-315-S1 is a Ka band scalar feed horn antenna with center frequency at 30 GHz and ± 3 GHz operation bandwidth. The antenna has 24 degree half power beamwidth with a typical of 16 dBi gain. The antenna offers lower than -25 dB sidelobe levels and supports both linear and circular polarization waveforms.

Model SOM-67314308-15-M1 is a free running V band mechanically tuned Gunn oscillator with +8 dBm output power from 60.0 to 74.0 GHz. It is composed of a Ka band broadband mechanically tuned Gunn oscillator which can produce +20 dBm output power with +/-3.5 GHz bandwidth and a V band passive X2 multiplier.

Model SFA-903983418-10KF-N1 is a W band X4 active multiplier with center frequency at 94 GHz with minimum ±4 GHz operational bandwidth. The active multiplier converts 22.5 to 24.5 GHz/+5 dBm input signal to +18 dBm output power in the frequency range of 90 to 98 GHz. The active multiplier has better than -25 dBc harmonic suppression.

Model STZ-12-I1 is an E Band full waveguide noise source. The noise source is silicon IMPATT diode based solid state noise source, which employs high performance diode and priority circuit design to offer nominal 14 dB ENR with extreme flatness in entire waveguide bandwidth from 60 to 90 GHz.

Model SFA-923963618-10SF-S1 is a W band X6 active multiplier with center frequency at 94 GHz with minimum ± 2 GHz operational bandwidth. The active multiplier converts 15.33 to 16.0 GHz/+5 dBm input signal to deliver 92 to 96 GHz frequency band with more than +18 dBm power. The active multiplier exhibits better than 60 dBc superior harmonic suppression performance. It draws 780 mA current from a +6 Vdc DC power supplier.

Model SWP-55365304-15-C1 is a V band waveguide four-way power combiner operates from 62 to 87 GHz. The power combiner exhibits 1.0 dB insertion loss and 20 dB port to port isolations between non-adjacent ports and 15 dB between adjacent ports in the operational bandwidth. The power combiner possesses excellent phase and amplitude balance.

Model SOV-77305215-12-I1 is an E band Varactor tuned InP Gunn oscillator which operates at 76.5 GHz center frequency with output power +15 dBm and ± 0.25 GHz voltage tuning bandwidth. The bias condition of the VCO is at +10.0 volts and 200 mA typically. To achieve ± 250 MHz, a voltage capable of swinging from 0 to +20 Vdc is required.

Model SAL-9239634001-094-C1 is a W band lens corrected antenna with center frequency at 94 GHz and ± 2 GHz operation bandwidth. The antenna has 1.2 degree half power beamwidth with a typical of 40 dBi gain. The design offers lower than -20 dB sidelobe levels and supports both linear and circular polarizations.

Model SBP-7438433012-1212-S1 is an E band power amplifier with center frequency at 79 GHz with ± 5 GHz operation bandwidth. The amplifier is designed and fabricated for emerging automotive ACC radar industry applications. The amplifier exhibits more than 30dB small signal gain with ± 3 dB gain flatness.

Model SBL-7438433060-1212-S1 is an E band low noise amplifier with center frequency at 79 GHz with ± 5 GHz operation bandwidth. The amplifier is designed and fabricated for emerging automotive ACC radar industry applications. The amplifier exhibits more than 30 dB small signal gain with ± 2 dB gain flatness and around 6.0 dB noise figure.

Model SFA-743843516-12SF-N1 is an E band X5 active multiplier with center frequency at 79 GHz with minimum ± 5 GHz operational bandwidth. The active multiplier is designed and fabricated for emerging automotive ACC radar industry applications. The active multiplier converts 14.8 to 16.8 GHz/+5 dBm input signal to deliver 74 to 84 GHz frequency band.

Model STH-2MSF-S1 is a harmonic mixer to cover the frequency range from 25 to 50 GHz with 2.4 mm (M) coaxial connector as RF input port and SMA (F) connector as combined LO/ IF port. The harmonic mixer exhibits minimum -20 dBm receiving sensitivity cross the entire 25 to 50 GHz with +13 dBm LO driving power level. The LO frequency range is 5 to 6 GHz and IF is 1 to 1.5 GHz.

Model SFD-753114-10SF-N1 is a GaAs Schottky beamlead diode based W band waveguide detector with negative output voltage polarity. The detector has 800mV/mW small signal detection sensitivity and +/-2.0 dB flatness in the entire 75 to 110 GHz operation frequency bandwidth.

Model SWC-151F-R1 and SWC-151M-R1 are V band waveguide to 1 mm coaxial adapters. These adapters offer convenient mean for waveguide to coaxial line connection for full V band operations. Both WR-15 waveguide to 1mm (F) and WR-15 waveguide to 1 mm (M) coax adapters have less than 0.8 dB insertion loss and better than 16 dB return loss from 50 to 75 GHz.

Model SWX-40360320-19-4B is a four port, 20 dB U-band full waveguide band crossguide coupler. Unlike most commercial available narrow band couplers, the new crossguide coupler covers full U band waveguide operation. The crossguide coupler exhibits less than 0.5 dB insertion loss, greater than 20 dB return loss, +/- 1 dB coupling flatness and better than 15 dB directivity over the entire 40 to 60 GHz frequency band.

Model STZ-10-I1 is a W Band full waveguide noise source. The noise source is silicon IMPATT diode based solid state noise source, which employs high performance diode and priority circuit design to offer nominal 12 dB ENR with extreme flatness in entire waveguide bandwidth from 75 to 110 GHz.

Model SK4-2734034540-KFKF-R1 is a broadband high isolation PIN diode single pole four throw switch. The switch operates from 26.5 to 40.0 GHz. It has better than 40 dB isolation and 5.5 dB typical insertion loss over the entire frequency range. The power handling and input P-1 dB of the switch is greater than +30 dBm CW.

Model SAT-603-14115-S1 is a V Band compact Orthomode Transducer (OMT) that operates at 61.5 GHz with 5 GHz operation bandwidth. This OMT exhibits 0.5 dB insertion loss, and 20 dB return loss. It also offers greater than 30 dB port to port isolation and cross polarization over the entire operating frequency band.

Model SFP-123KF-S1 is a resistive diode based passive tripler. The tripler is designed and build with a balanced waveguide configuration, which offers low harmonic emission and high conversion efficiency. The tripler exhibits 20 dB typical conversion loss and converts +20 dBm input power at 20 to 30 GHz to 0 dBm minimum output power at 60 to 90 GHz.

Model SFS-60390315-10VFSF-S1 is an E-Band, subharmonically pumped mixer. The mixer employs high performance GaAs Schottky beamlead diodes, balanced configuration to produce superior RF performance. The subharmonically pumped mixer is capable for full RF waveguide band operation for RF frequencies from 60 to 90 GHz with half of the LO frequency: 30.0 to 45.0 GHz.

 Model SWF-60390350-28-L1 is a custom designed Ka-Band waveguide lowpass filter. The filter features low insertion loss and high rejection. The filter shows 1.2 dB maximum insertion loss from 26 to 60 GHz and greater than 50 dB rejection in the frequency range of 90 to 145 GHz.

Model SWC-101F-R1 and SWC-101M-R1 are W band waveguide to 1 mm coaxial adapters. These adapters offer convenient mean for waveguide to coaxial line connection for full W band operations. Both WR-10 waveguide to 1mm (F) and WR-10 waveguide to1 mm (M) coax adapters have less than 1.0 dB insertion loss and better than 15 dB return loss from 75 to 110 GHz.

Model SBP-1031133040-SFSF-C1 is an X band power amplifier which delivers 30 dB small signal gain and 10 W linear power to cover 9.5 to 10.5 GHz frequency range. The amplifier integrates input and output isolators to offer better than 1.2:1 VSWR and safe operation when input or output show extreme load conditions.

Model SSS-24307-27M-S1 and SSS-24307-27M-D1 speed sensor heads are based on Doppler principle. While Model SSS-24307-27M-S1 is designed and manufactured for moving target speed measurement, Model SSS-24307-27M-D1 is for both speed and direction detection measurement. The operation frequency and output power of the models are at 24.125 GHz and 7 dBm, respectively.

Model SFB-15-N2 is a V-Band, externally biased balanced mixer. The mixer employs high performance GaAs Schottky beamlead diodes, balanced configuration and proprietary bias circuitry to produce superior RF performance with very low LO pumping level. The externally biased mixer is capable for full RF waveguide band operation for both LO and RF frequencies from 50 to 75 GHz.

Model STC-12-S1 is a single sideband E-Band down converter, which down convert the entire E Band frequency, 60 to 90 GHz, to an IF frequency from 2 to 32 GHz. The converter includes a Gunn oscillator, a full band balanced mixer, a highpass filter and a full band isolator. The built-in Gunn oscillator operates at 58 GHz with + 5.0 volts at 450 mA DC bias.

Model SOM-77302320-12-S1 is a free running E band mechanically tuned Gunn oscillator with output power 20 dBm and tuning bandwidth +/- 1 GHz. The mechanical tuning is accomplished via a self-locking tuning screw or micrometer. The bias voltage and current to operate the oscillator is at +10 Vdc and 200 mA typically. The oscillator is also bias tunable to allow frequency modulation via its bias port.

Model SWD-1040H-10-SB is a 10 dB W-band high directivity directional coupler. The directional coupler is based on traditional multi-hole coupling mechanism. The directional coupler is constructed with machined brass waveguide housings. With detailed electrical/mechanical design and precision fabrication process, the directional coupler offers instrumentation quality and superior RF performance.

Model SWC-222F-R1 and SWC-222M-R1 are Q band waveguide to coaxial adapters. These adapters offer a convenient mean for waveguide to coaxial connector transition. These adapters have less 0.3 dB insertion loss and better than 18 dB return loss in frequency range of 33 to 50 GHz for both 2.4 mm (F) and 2.4 mm (M) connector types.

Model SFB-06-E2 is a D-Band, externally biased balanced mixer. The mixer employs high performance GaAs Schottky beam lead diodes, balanced configuration and proprietary bias circuitry to produce superior RF performance with very low LO pumping level. The low LO pumping level is desirable feature at higher millimeter-wave bands.

Model SFS-75311416-10VFSF-S1 is a W-Band, subharmonically pumped mixer. The mixer employs high performance GaAs Schottky beamlead diodes, balanced configuration to produce superior RF performance. The subharmonically pumped mixer is capable for full RF waveguide band operation for RF frequencies from 75 to 110 GHz with half of the LO frequency: 37.5 to 55.0 GHz. The conversion loss measured was 12 to 16 dB at +13 dBm LO pumping level typically.

Model SSD-24310-22L-S1 and SSD-24310-22L-D1 are K band FMCW ranging sensors. While model SSD-24310-22L-S1 offers single channel output for speed and ranging sensing only, model SSD-24310-22L -D1 offers speed, direction and ranging sensing simultaneously. The sensors operate at 24.125 GHz with +/-150 MHz frequency modulation bandwidth and 10 dBm nominal output power.

Model SWC-121F-E1 is an E band waveguide to coaxial inline adapter. The adapter offers a convenient mean for WR-12 waveguide to 1mm (F) connector transition. The inline configuration offers convenient mean for the coaxial testing cable to waveguide adaption.

Model SNW-1431530320-51-IH2 is a WR-51 waveguide high power isolator. The isolator is a junction type isolator, which has less than 0.25 dB insertion loss and better than 25 dB isolator in the frequency range of 14.0 to 14.5 GHz.

Model SFP-10328-S1 is a resistive diode based passive tripler. The tripler is designed and build with a balanced waveguide configuration, which offers low harmonic emission and high conversion efficiency. The tripler exhibits 20 dB typical conversion loss and converts +20 dBm input power at 25 GHz to 37 GHz to 0 dBm power at 75 to 111 GHz.

Model SWC-101F-E1 is a W band waveguide to coaxial inline adapter. The adapter offers a convenient mean for WR-10 waveguide to 1 mm (F) connector transition. The inline configuration offers convenient mean for the coaxial testing cable to waveguide adaption.

Model SOL-24307-42-VG is a low cost, production ready K band Varactor tuned Gunn oscillator. The center frequency of the VCO is set at 24.125 GHz with +/-150 MHz frequency modulation bandwidth and +7 dBm nominal output powers. The VCO operates from a single +5 .0 Vdc power supplier and typically draws 250-mA current and requires 0 to +15 volts voltage swing for electrical tuning.

Model SSP-24305-42-S1 is a low cost, production ready K band FMCW ranging sensor module. The center frequency of the module is set at 24.125 GHz with +/-150 MHz frequency modulation bandwidth and +5 dBm nominal output power. The sensor operates from a single +5 .0 Vdc power supplier and typically draws 250-mA current and requires 0 to +15 volts voltage swing for electrical tuning.

Model SSP-24303-42-D1 is a low cost, production ready K band FMCW ranging and directional sensor module. The center frequency of the module is set at 24.125 GHz with +/-150 MHz frequency modulation bandwidth and +3 dBm nominal output powers. The sensor operates from a single +5 .0 Vdc power supplier and typically draws 250-mA current and requires 0 to +15 volts voltage swing for electrical tuning.

Model SNF-42-I1 is a full waveguide band junction isolator covering the frequency range from 18 to 26.5 GHz in WR-42 waveguide band. The isolator offers 0.3 dB typical insertion loss and 8 dB minimum isolation. The operating temperature is from -35 to +60 °C and the forward power handling is 2 W minimum.

Model SOD-01213-22-S1 is a 37 GHz dielectric resonator oscillator (DRO). The oscillator is a free running oscillator and the high frequency stability is achieved by implementing a high quality dielectric resonator. The oscillator exhibits +13 dBm output power and low phase noise of -95 dBc/Hz at 100 KHz offset.

Model STE-SF906-00-N1 is a D band frequency extender, which extends the input frequency of 12 to19 GHz to a full waveguide bandwidth, 110 to 170 GHz operation. The frequency extender combines high performance millimeter passive multipliers, amplifiers and filters to extend the low frequency sweeper or synthesizer to D band frequency band.

Model SFA-243403215-28SF-W1 is an active frequency multiplier to cover the output frequency range of 24 to 40 GHz. The required input power is +5 dBm and achieved output power is +13 dBm, which is sufficient to drive a Ka band balanced mixer to form a low cost down converter module.

Model SWL-4247-S1 is a WR-42 waveguide high power matching load. The load offers better than 1.20:1 VSWR in the frequency range of 18.0 to 26.5 GHz. The power handling of the load is 50 W CW. The load measures 1.75” W x 6.30” L x 1.75” H.

Model SFQ-94394312-1010SF-S1 is a W-Band quadrature (I/Q) mixer. The mixer employs high performance GaAs Schottky beamlead diodes, balanced configuration and proprietary circuitry to produce superior RF performance.

Model SAS-693-14115-F1 is a 66 to 72 GHz Linear to Circular Polarizer. The polarizer exhibits 1.0 dB maximum insertion loss, 1.3:1 VSWR and 1.2 dB axial ratio. The RF interface is 0.141” diameter circular waveguide with UG385/U flange for standard WR-15 waveguide interface.

Model SOD-01213-22-S1 is a 37 GHz dielectric resonator oscillator (DRO). The oscillator is a free running oscillator and the high frequency stability is achieved by implementing a high quality dielectric resonator. The oscillator exhibits +13 dBm output power and low phase noise of -95 dBc/Hz at 100 KHz offset. The frequency stability of the oscillator is +/- 3 ppm per degree C or better in the temperature range of -40 to +85° C.